 |
OSCO
Model GSLG-A Automatic Slide
Gate Opener are designed for large heavily used industrial
gates that require continuous duty application.The
model VS-GSLG is a Variable Speed
slide gate operator. The variable speed operator starts and
stops at a slower speed. This is less stressful on the sliding
gate mechanism of the operator and gate and lessens the maintanence
on the gate components. This effort may slow down the operation
of the opening time by a second or so but it is your gate
and maintenance crews will so appreciate it. For
a quick look at a reference chart look see our automatic
slide gate opener chart selector or swing gate
chart selector. |
Now offering FREE SHIPPING on all GTO Operators!
| Cabinet: |
Electrical: |
- Weather-resistant
galvannealed steel cabinet with powder coat finish
- Lockable,
gasketed, hinged and removable front cover for easy acces
|
- Variable
speed - soft start/soft stop programmable through an inverter
motor control (voltage and phase of input power required
at time of order)
- Available
from 1/2 HP to 2 HP industrial continuous-duty, three
phase, 56-frame motors
- Available
in all standard voltages and phases
- Maximum
run timer for clutch and motor protection
- Double
C-face brake
- Power
on/off switch
- Duplex
receptacle on 115 VAC units
- Three-button
control station included
- Accessory
connections are 24-volt AC or DC
- Easily
adjustable rotary limit switches
- Full
system capable for access controls and reversing devices
|
| Mechanical: |
- Heavy-duty 10:1 right-angle C-face gear reducer
- #50
roller chain and sprocket
- Adjustable torque limiter
- Heavy-duty pillow-block bearings
|
| Mounting: |
Manual
Release: |
- 3
- 3 1/2" OD post mounting
- Optional
pad mounting pedestal available
|
- Manual
release is easily accessible
|
| Anti-Entrapment/Detection
Devices: |
Control
Circuit: |
- Operator
is pre-wired to accept contact and non-contact detection
devices such as contact edges and/or photo electric eyes.
|
- Solid state circuit board, 24 VDC
- Multiple LEDs for easy setup and troubleshooting
- Built in maximum run timer and auto close timer
- Right-hand/left-hand easy conversion
- Master/Slave - simple three-wire connection
|
| Warning
Signals: |
- Continuous
tone entrapment alarm
- Warning
beeper to sound when gate is moving
- Pre-start
audio/visual outputs included
|
 |
 |
GSLG-A
Slide Gate Opener |
Variable
Speed slide gate operator |
Typical Application for the GSLG-A and the VS-GSLG Variable
Speed Slide Gate Opener
 |
 |
With
a Single Gate you need one Units |
With
a Double Gate you need Two Units |
| Model |
HP |
Voltage |
Phase |
Maximum
Gate Operator Weight |
Cantilever
Type |
Roller
Type |
Overhead
Type |
List
Price |
Order
Now |
| GSLG-A-211 |
1/2 |
115 |
Single |
1100
lbs |
25
ft. |
35
ft |
45
ft |
$3,291.31 |
|
| GSLG-A-421 |
3/4 |
230 |
Single |
1400
lbs |
30
ft |
42
ft |
60
ft |
$3,343.71 |
|
GSLG-A-183
|
1 |
208 |
Three |
2200
lbs |
40
ft |
56
ft |
78
ft |
$3,521.03 |
|
| Variable
Speed - Industrial Slide Gate Opener |
| VS-GSLG-211 |
1/2 |
115 |
Single |
1100
lbs |
45
ft |
35
ft |
45
ft |
$4,501.51
|
|
| VS-GSLG-121 |
1 |
230 |
Single |
2500
lbs |
40
ft |
56
ft |
78
ft |
$4,645.40
|
|
| VS-GSLG-783 |
2 |
208 |
Three |
4000
lbs |
- |
- |
100' |
$4,979.89
|
|
| 2500-2015
- 100 ft. cable Master//Slave communication wire...... $75.00 |
|
| Double-swing--
Two Operators required- Slave capability is built in |
| 2500-2207
- Low Voltage Surge suppressor ............................
$42.00 |
|
| 2510-262
- 115V Heater ....................................................
$112.00 |
|
| 2510-273
- 230V Heater ....................................................
$175.00 |
|
| 2520-354
- 460V Heater ....................................................
$250.00 |
|
 |
Caution:
Automatic gates are not for pedestrians! Automatic gate operators
are designed for vehicular traffic only.Tthey are powerful
and can cause serious injury or death. Accordingly, direct
all pedestrian traffic to a separate pedestrian gate. UL325
requires the use of contact or non-contact anti-entrapment
devices. ASTM F2200 requires that all exposed rollers are
covered. |
|
